WHEN YOU DEMAND HIGH QUALITY AND ACCURACY, GO WITH........ SPEED CITY !

MOPAR
FORD
MISC
PARTS
GM
DRAGSTER
 
Testimonials
Model Gallery
In Progress
Coming Soon
Model News
Order Form
Contact Us
Want's
Links
 

"FORD MODELS"
Ford - Lincoln - Mercury

Solution Graphics

 

Doug Nash's
BRONCO BUSTER
Ford Bronco Half Cab Long Nose Funny Car


#SC-104 ........ $42.00

Resin model includes:Correct Body, Chassis, Straight Tube Front Axle (with coil over shocks),
Ladder Bars, Rear Shocks, Firewall, Cowl, Grill & 2- Front Bumper options.

Recommended donor parts:
#SC-38 Halibrand 15" Front Mag Wheels (use for rear mags on early version)..... Inner Rims are included.
The center cap needs to be drilled out if using the Halibrands.
#SC-57 S/S Cragar Rear Mag Wheels (for later version)
#SC-87  Inner Rims (deep dish) (for later version)
#SC- 106 American 18" 12 Spoke Mag Wheels
#SC- 105 Ford (small block) Injection "Parts Pack"
#SC-93
Ford 9 Inch Rear End
#SC-7
AFX Parts Pack - Needed for: Push Button Transmission Console, Tachometer, Gas Cap, Fuel Pump,
Master Cylinder, Timing Balancer Pulley & Steering Box.
#SC-103 Drag Racing Driver Figure

> Use AMT/ERTL 1967 Mustang GT for: 289 Ford small block engine.

> Standard 18" Goodyear Dragster Tires will be needed (found in most dragster kits).

> Use Revell Ford T Roadster for: Headers, Radius Rods & Spindles- (if poseable wheels are desired).

> Use AMT Goodyear Blue Streak 9:00 x 15" Slicks (found in older AMT kits).

> Visit the MODEL NEWS page for tips on making a "Flip Front-End".

> To make the interior tin..... Fit a piece of .020" sheet inside the body,
glue the cowl to the sheet and remove the center section.

> To set the ride height for your coil over shocks..... Use a 9 volt battery placed under the front part of the frame.

> To set the front axle..... Springs should face the rear of the axle.
> Use Revell Ford Thunderbolt kit to replace all 4 shocks if desired.

> Correct colors are: House Of Kolor (or) Bob's Paint's "Candy Lime" and "Candy Burgundy".

Visit the "IN PROGRESS" page to see the extensive work that was done to this new item *


 

STONE, WOODS & COOK
DARK HORSE 2
'66 Long Nose AWB Mustang Funny Car



Approved and Authorized by Mike Cook


Mock up using a Polar Lights Charger or Barracuda Funny Car Chassis


#SC-17 ......... $38.00

 Resin kit includes: Correct Body (with semi-hollow door handles), Interior Tub (with custom seat), 2- Inner Body Bracing's,
Honeycomb Grill, Front Bumper, Thunderbird Tail Lights and Porsche style Trunk Vent.

Recommended donor parts:
#SC-103 Drag Racing Driver Figure
#SC-91 Buick / Olds/ Pontiac Rear End
#SC-66 392 Hemi Engine
#SC-64
Funny Car Parts Pack (for Airheart Disk Brakes, Blower Pulleys, Ideler Arm, 392 Timing Cover,
4-Port Injectors, Tranny Linkage, Oil Filter & MallorySuper Coil.
#SC-83 Ribbed Blower Belt
#SC-57 S/S Cragar Rear Mag Wheels
#SC-87  Inner Rims (deep dish)
#SC-80 Halibrand 16"(deep dish) Rear Mags (for later version)
#SC-75
Goodyear Blue Streak Skinny Front Tires...... (as you can see, the Polar Lights Front Tires are too small)
#SC-34 S/S Cragar (zero offset) Front Mag Wheels

*An amt/ertl '67 Mustang is needed for the Grill Insert and Rear Bumper.

*A Polar Lights Charger or Barracuda Funny Car is need for a donor chassis

*A Monogram/Revell '66 Shelby Mustang GT 350H (for side windows).

*Model King "Hemi Under Glass" for headers..... or make them from solder?

*392 Hemi and Scoop can be found in the Revell Miss Deal.
or use our #SC-66 (1-piece) 392 HEMI ENGINE, found on the "Parts Page".

*The Revell S.W.C Willys (Black) Gasser also has a 392 Hemi Engine and a one-piece Scoop.

*If doing a flip front end, you will need to scribe out the "pre-scribed front clip"
and use the hinge directions on the "MODEL NEWS" page.

Stone, Woods & Cook decals.
(you'll need to reverse the ribbons on the front fenders)

Jim Polli built this from a resin model.

Ran Ramsay built this from a resin model.
Winning 3 category's..... BEST DETAIL, FAST ON THE QUARTER MILE & BEST IN SHOW,
at the Wally Parks N.H.R.A. Motor sports Museum "SPIRT OF SPEED" Model Contest on Nov 8 2015


 

Jack Ditmars'
Lil' SCREAMER
'34/'37 FORD ALTERED COUPE
1/25 scale



#SC-22 ......... $44.00

Resin model includes: Correct Body, Hood, Frame (with Shackle, roll bar & motor mount locator pins),
Seat, Drive Shaft Tunnel, Firewall/Doghouse, Hilborn Small Block Chevy Injection Manifold and 2-piece Hood Sc
oop.

Recommended donor parts:
#SC-001 Lil Screamer decals
#SC-103 Drag Racing Driver Figure
#SC-93
Ford 9 Inch Rear End
#SC-100 Wheelie Bars
#SC-99
Goodyear Blue Streak 16" Drag Slicks
#SC-85
 American "TORQUE THRUST" 16" Deep Dish Mags (for later version)
#SC-87  Inner Rims (deep dish)
#SC-75
Goodyear Blue Streak Skinny Front Tires
#SC-49 American 12 Spoke Front Mag Wheels
#SC-7 AFX Parts Pack
#SC-25 10" Aluminum Hollow Tube Injector Stacks

*See "MODEL NEWS" page for instructions on how to make a front tube straight axle.

*If building the version with the "Deep Dish Cragar's", those can be found in the MPC "Mummy Machine.

*Originally this car ran a small block 289 Chevrolet Corvette Engine and later to a 350.

Photo's of the roll bar dimensions ........ ......... ......... There are roll bar locator pins on the models chassis.

Scott Kapellusch built this from a resin model.
UPDATE: This model took BEST IN SHOW at the Wally Parks N.H.R.A. Motorsports Museum
"SPIRIT OF SPEED" Model Contest on Nov 5 2017


 

1966 LONG NOSE MUSTANG FUNNY CAR





#SC-19 ......... $42.00

This is the only accurate '66 Mustang Funny Car on the market
and has the only Correct Altered Front Wheel Base !

Resin model includes: Correct Body (with semi-hollow door handles), Hood, 2- piece Chassis & Interior Tub,
Dash & Custom rear spoiler.

Recommended donor parts:
#SC-103 Drag Racing Driver Figure
#SC-100 Wheelie Bars
#SC-93 Ford 9 Inch Rear End
Check out our "PARTS PAGE" for any Tires, Slicks, Mag Wheels, Rear End or other parts you may need.

*A Model King Mustang Funny Car Kit will be needed for the engine, glass and interior parts.

*Use amt/ertl's '67 Mustang G/T for "alternate" poseable front suspension, rear axle, shocks & leaf springs.

Contact Nikki at: poppawheelie65@yahoo.com for the "Tommy Grove" Mustang decals.

Has the Batcar, Bardahl Ford, Daddy Warbucks & Tasca Ford decals to specifically fit our body !

Jim Polli built this from a resin model.

Doug Schultz built this from a resin model.

Scott Kapellusch built this from a resin model.

Chris Cantler built this from a resin model.


All rights reserved. Do not copy any Speed City Resin bodies or parts without permission and consent.