|
|||||
WHEN YOU DEMAND HIGH QUALITY AND ACCURACY, GO WITH........ SPEED CITY ! |
The
first and only correct '67-'68 Barracuda F/C in model history, never
before seen in model kit form..... until now !
Our
goal was to give you an accurate body to represent the cars shown above.
The Polar Lights Barracuda F/C body is NOT correct for any of these cars or even what they
show on their box art.
None of these Barracuda Funny Cars shown had stretched bodies, only an altered front wheelbase & wider rear wheel wells.
Check the "IN PROGRESS" page to see the extensive work that was done to make this model.
With all our extra body parts, there are more than 30 ways to build this Speed City Resin Model.
*Check out our "PARTS PAGE" for any Tires, Slicks, Mag Wheels, Rear End, Driver Figure or other parts you may need.
*To build some cars you may need to Hog-out or Flare the rear wheel well.
*We thought of doing a "RAKED ROOF VERSION", but all the roofs are
raked differently.
*To rake the roof, you will need to cut & re-set the A-Pillars (windshield
posts).
*Back up the cut post with a piece of paper clip or stainless steel wire (found
at hobby stores) for strength !
*A
Polar Lights Barracuda or Charger F/C will be needed for a donor kit (but will need to be shortened just before the engine).
CANDIES & HUGHES decal
TOM McEWEN decal
SUPER CUDA decal
CHI-TOWN HUSTLER decal (decal will need to be cut shorter at the door line to fit)
FLINTSTONE FLYER
decals to fit this body.
FRED GOESKE decals
to fit this body.
KING FISH Barracuda decal .............
Jim Polli built this from a resin model.
"
We guarantee this to be the only correct '65 Coronet Hardtop A/FX ever offered
"
Resin model includes: Correct AWB Body, (with window & door trim & Corrected Tail Lights, ). Hood, A.W.B. Chassis, Interior tub, Coronet Dash, Single Headlight grill and Double Headlight grill (w/ block-out head lights), Front & Rear Bumpers.
Recommended donor parts:
#SC-103 Drag Racing Driver Figure
#SC-90 Chrysler Dana 60 Rear End (for factory built AFX cars)
#SC-55 Front Leaf Spring Assortment Pack (for none factory cars)
#SC-45 AFX (low profile) Blue Streak Drag Slicks
#SC-40 American Racing 15" Rear Mag Wheels
#SC-87 Inner Rims (deep dish)
#SC-72 AFX - Super Stock Skinny Front Tires
#SC-39 American 5 Spoke Front Mag Wheels
#SC-82 A-100 Lightweight Super Stock Seats
#SC-7 AFX Parts Pack
#SC-64 Funny Car Parts Pack
#SC-24- 25 or 26 15"-10" or 7" Hollow Tube Injector Stacks
*You
can set the height of the front end by adding plastic blocks as "risers"
to the kit suspension or frame, or use a
dropped axle (that most of the cars used), from a Revell '51 Ford Anglia,
'51 Henry J, '29 Ford or Custom pick up, kit.
*
Use
any Lindburg '64 Plymouth or '64 Dodge for a donor kit.
*A hood scoop ( if needed ) can be found in the Lindburg '64 Dodge Ramchargers kit *
Mr. NORMS Red & Sliver Coronet decals.
DICK LANDY Coronet decals.
DICK LANDY'S Coronet AFX. decals
Contact Nikki at: poppawheelie65@yahoo.com for the "RAMCHARGERS" decal.
Contact Nikki at: poppawheelie65@yahoo.com for the "HONKER" decal
Gary E. Kennedy built this from a resin model.
Roger Isenhouer built this from a resin model.
(His first AWB model) Used Lindburg '64 Dodge Ramcharger decals.
Doug Schultz built this from a resin model.
"
We guarantee this to be the only correct '65 Dodge Coronet Sedan A/FX ever offered
"
THIS
ITEM IS UNAVAILABLE AT THIS TIME, PLEASE DO NOT ORDER !
Rick Shepard built this from a resin model.
"
We guarantee this to be the only correct '65 Plymouth Hardtop A/FX ever offered
"
THIS ITEM IS UNAVAILABLE AT THIS TIME, PLEASE DO NOT ORDER !
Recommended donor parts:
#SC-103 Drag Racing Driver Figure
#SC-90 Chrysler Dana 60 Rear End (for factory built AFX cars)
#SC-55 Front Leaf Spring Assortment Pack (for none factory cars)
#SC-45 AFX (low profile) Blue Streak Drag Slicks
#SC-40 American Racing 15" Rear Mag Wheels
#SC-87 Inner Rims (deep dish)
#SC-72 AFX - Super Stock Skinny Front Tires
#SC-39 American 5 Spoke Front Mag Wheels
#SC-82 A-100 Lightweight Super Stock Seats
#SC-7 AFX Parts Pack
#SC-64 Funny Car Parts Pack
#SC-24- 25 or 26 15"-10" or 7" Hollow Tube Injector Stacks
*Use
any Lindburg '64 Plymouth or '64 Dodge for a donor kit. (The Dodge works best for firewall and inner wheel wells).
*A hood scoop ( if needed ) can be found in the Lindburg '64 Dodge Ramchargers kit *
*You
can set the height of the front end by adding plastic blocks as "risers"
to the kit suspension, or use a
dropped axle from a Revell '51 Ford Angelia,
'51 Henry J, '29 Ford or Custom pick up kit.
Has the SOX & MARTIN GATE CITY decal.
Southern Motorsports Hobbies has the SOX & MARTIN GATE CITY decal in stock at this time.
*Contact Nikki at: poppawheelie65@yahoo.com for The
"Maloney Plymouth" decal.... Also on eBay !
*Contact Nikki at: poppawheelie65@yahoo.com for The "Golden Commandos" decal..... Also on eBay !
Cecil Yothers MELROSE MISSILE decals for this kit.
Doug Schultz built this from a resin model.
Ron Ramsay built this from a resin model.
"
We guarantee this to be the only correct '65 Plymouth Sedan A/FX ever offered
"
#SC-33
..... $48.00
THIS ITEM IS UNAVAILABLE AT THIS TIME, PLEASE DO NOT ORDER !
Resin
model includes: Correct AWB '65 Ply Body, Chassis, Hood, Interior tub, Dash,
Separate Grill (w/ block-out head lights), Front & Rear Bumpers & Taillights.
Recommended donor parts:
#SC-103 Drag Racing Driver Figure
#SC-90 Chrysler Dana 60 Rear End (for factory built AFX cars)
#SC-55 Front Leaf Spring Assortment Pack (for none factory cars)
#SC-45 AFX (low profile) Blue Streak Drag Slicks
#SC-40 American Racing 15" Rear Mag Wheels
#SC-87 Inner Rims (deep dish)
#SC-72 AFX - Super Stock Skinny Front Tires
#SC-39 American 5 Spoke Front Mag Wheels
#SC-82 A-100 Lightweight Super Stock Seats
#SC-7 AFX Parts Pack
#SC-64 Funny Car Parts Pack
#SC-24- 25 or 26 15"-10" or 7" Hollow Tube Injector Stacks
*Use
any Lindburg '64 Plymouth / '64 Dodge for a donor kit. (The Dodge works best for firewall and inner wheel wells).
*A hood scoop ( if needed ) can be found in the Lindburg '64 Dodge Ramchargers kit *
*You
can set the height of the front end by adding plastic blocks as "risers"
to the kit suspension (Frame), or use a
dropped axle from a Revell '51 Ford
Angelia, '51 Henry J, '29 Ford or Custom pick up kit.
TEMPTATION Decal is on the "MISC. PARTS PAGE"
Contact Nikki at: poppawheelie65@yahoo.com for the "Jakes Speed Equipment" & "UFO" decal.
If your building the Jakes Speed Equipment you must take a scale 8" out of the rear in the middle of the trunk.
It also has no cowl as the injectors set 1" away from the glass. This info. comes from the crew chief: Jet Townsend.
Scott Kapellusch built this from a resin model.
Doug Schultz built this from a resin model.
Ron Ramsay built this from a resin model.
" APPROVED & AUTHORIZED BY CECIL L. YOTHER "
Resin
model includes:Correct AWB '65 Ply Body, Chassis, Hood, Interior tub, Dash,
Separate Grill (w/ block-out head lights), Front & Rear Bumpers & Taillights.
Recommended donor parts:
#SC-103 Drag Racing Driver Figure
#SC-90 Chrysler Dana 60 Rear End
#SC-82 A-100 Lightweight Super Stock Seats
#SC-45 AFX (low profile) Blue Streak Drag Slicks
#SC-57 S/S Cragar Rear Mag Wheels (for later version)
#SC-3 Reversed Halibrand Mag Wheels (for early version)
#SC-87 Inner Rims (deep dish)
#SC-72 AFX - Super Stock Skinny Front Tires
#SC-39 American 5 Spoke Front Mag Wheels
#SC-5 Hemi Hilborn Intake Manifold
#SC-25 10" Injector Stacks
#SC-7 AFX Parts Pack - For:
Push Button Transmission Console, Tachometer, Gas Cap, Fuel Pump, Master Cylinder, Timing Balancer Pulley & Steering Box.
#SC-64 Funny Car Parts Pack
#SC-56 Parchute Assortment Pack
*Use
any Lindburg '64 Plymouth or '64 Dodge for a donor kit. (The Dodge works best for firewall and inner wheel wells).
*You
can re-set the height of the front end by adding plastic blocks as "risers"
to the kit suspension.
Virgil Stanbary built this from a resin model.
THIS ITEM IS UNAVAILABLE AT THIS TIME, PLEASE DO NOT ORDER !
This is not a copy of the incorrect mpc kit.
Our model has been re-mastered with new accurate:
Lengthened body, altered front wheel wells, rear wheel well flares, B- pillars & lengthened chassis rails.
Made into a 1-piece body.
See the
"IN PROGRESS" page for details.
#SC-
12 ...... $42.00
Recommended donor parts:
#SC-103 Drag Racing Driver Figure
#SC-90 Chrysler Dana 60 Rear End
#SC-85 American "TORQUE THRUST" 16" Deep Dish Mags
#SC-87 Inner Rims (deep dish)
#SC-99 Goodyear Blue Streak 16" Drag Slicks
#SC-75 Goodyear Blue Streak Skinny Front Tires
#SC-66 392 Hemi Engine (1-piece)
#SC-50 M/T 392 Hemi Valve Covers (fins & logo need to be sanded off)
#SC-64 Funny Car Parts Pack
#SC-7 AFX Parts Pack
#SC-83 Ribbed Blower Belt
*Recommended donor kits: the Model King Kenz & Leslie Cougar Funny Car or the GTO Funny Car.
*Glass can be made using clear plastic sheet or get an amt Charger III model kit for the kit glass.
THE FLYING DUTCHMAN Charger III decals.
#SC-29......... $48.00
THIS
ITEM IS UNAVAILABLE AT THIS TIME, PLEASE DO NOT ORDER !
Resin
model includes: Correct AWB 1966 Dodge Dart Funny Car Body (with Semi-Hollow door handles),
Chassis,
Interior tub, Front grill, F&R Bumpers, Taillights & 2- Left & Right "Rear Patch Panels".
Recommended donor parts:
#SC-103 Drag Racing Driver Figure
Check out the "PARTS PAGE" for any Tires, Slicks, Mag Wheels, Rear End, Wheelie Bars or other parts you may need.
*Every Dart Funny Car had some differences .... (wheelbase, long nose / short nose, stock bumper, cut bumper, etc)
You will
need to make some alterations to build an individual car, although with this model, any one of these cars can be built.
*Two rear "PATCH PANELS" are supplied to do the rear wheel alterations
if needed ?
Some of the cars ran stock location rear wheel wells.
*Chassis was
designed to use Amt/Ertl Funny Cars for front & rear suspension, but
will also except other suspensions
with some minor modification.
*For
a pose able front axle... Use
a dropped axle from a Revell '51 Ford Angelia, '51 Henry J, '29 Ford or Custom
pick up.
*See "MODEL NEWS" page for instructions on how to make a front tube straight axle.
*Visit the MODEL NEWS page for "HOW TO" tips on: "Flip Front-End".
Click on photo for a printable instruction sheet to do any alterations.
Ron Ramsay built this from a resin model.
Scott Kapellusch built this from a resin model.
Scott Kapellusch built this from a resin model.
Jim Polli built this from a resin model and Fremont decals
Has these decals for our Long Dart Funny Car-
*Charlie Allen's PURPLE TERROR
*Charlie Allen's ATLANTIC FLYER
*The FLYING DUTCHMAN Topless Dart
*Gene Snow RAMBUNCTIOUS
*Rambunctious Interior MACHINE TURN decals
Approved
and Authorized by Rick Williamson Owner of "The HAIRY CANARY"
Mastered from an original '66 Plymouth Valiant promo model.
THIS ITEM IS UNAVAILABLE AT THIS TIME.
Resin model includes: Correct AWB '66
Valiant Body, Hood, Interior Tub, Square Tube Chassis, Grill (with block-out
Headlights), Grill Insert, Steering Column Box (with gauges), Bumpers &
Taillights.
*Although
hard to see in the photo, the side chrome body trim is there, along with all
the correct sail panel moldings.
This
kit was designed to build both (early & later versions).
Recommended donor parts:
#SC-103 Drag Racing Driver Figure
#SC-91 Buick / Olds/ Pontiac Rear End
#SC-55 Front Leaf Spring Assortment Pack (for 1/4 elliptical springs used on rear axle)
#SC-45 AFX (low profile) Blue Streak Drag Slicks
#SC-40 American Racing 15" Rear Mag Wheels
#SC-87 Inner Rims (deep dish)
#SC-75 Goodyear Blue Streak Skinny Front Tires
#SC-39 American 5 Spoke Front Mag Wheels
#SC-69 Hilborn Bug Catcher
#SC-56 Parchute Assortment Pack
#SC-66 392 Hemi Engine (1-piece)
#SC-50 M/T 392 Hemi Valve Covers
#SC-83 Ribbed Blower Belt
#SC-64 Funny Car Parts Pack
*To
build the later version (lowered & set back engine) you will need to cut
out part of the firewall &
floorboard,
and build an L-shaped box in the interior tub to surround the engine.
you will also need to re-set the transmission mount.
*A Model King AWB Funny Car kit will supply the suspension
& interior parts.
*For
a poseable front axle.....Use
a dropped axle from a Revell '51 Ford Angelia, '51 Henry J, '29 Ford or Custom
pick up, kit.
Scott Kapellusch built this from a resin model.
This new redesigned chassis, wheel base & Interior tub actually fits !........ (unlike the original kit)
* Mock-up model above has Model King "Hemi Under Glass" donor suspension parts *
Resin
model includes: Correct Body, Hood, New Rear Engine Chassis, New Interior Tub, Grill &
Bumper,
Grill Insert, Valance, Rear Bumper & Taillights.
*Model King" HEMI UNDER GLASS" is all you need for a donor kit.
Recommended donor parts:
#SC-103 Drag Racing Driver Figure (for all versions)
"HEMI UNDER GLASS VERSION"
#SC-43 Goodyear 15" Drag Slicks
#SC-89 Chrysler 8 3/4 Rear End
#SC-65 Hurst Mag Wheels
#SC-87 Inner Rims (deep dish)
#SC-72 AFX- Super Stock Front Racing Tires
#SC-7 AFX Parts Pack
#SC-64 Funny Car Parts Pack
"TOM McEWEN VERSION"
#SC-43 Goodyear 15" Drag Slicks
#SC-87 Inner Rims (deep dish)
#SC-89 Chrysler 8 3/4 Rear End
#SC-75 Goodyear Blue Streak Skinny Front Tires
#SC-7 AFX Parts Pack
#SC-64 Funny Car Parts Pack
#SC-56 Parchute Assortment Pack ( HEMI CUDA has dual chutes)
"FRED GOHSKE VERSION"
#SC-99 Goodyear Blue Streak 16" Drag Slicks
#SC-79 Halibrand (shallow dish) 16" Mag Wheels
#SC-88 Inner Rims (shallow dish)
#SC-89 Chrysler 8 3/4 Rear End
#SC-75 Goodyear Blue Streak Skinny Front Tires
#SC-7 AFX Parts Pack
#SC-64 Funny Car Parts Pack
#SC-56 Parchute Assortment Pack ( FRED GOSKE has dual chutes)
Tom McEwen PLYMOUTH DEALERS Hemi Cuda
HURST HEMI UNDER
GLASS decals
Damian Fontes built this from a resin model.
Ron Ramsey built this from a resin model.
Scott Kapellusch built this from a resin model.
This was the 1st resin model made for Speed City. Put in production on June 7 2006.
In 2009 it was upgraded with correct AWB chassis/ Interior floor, firewall,
front frame clip, door panels & stock front wheel wells.
#SC-1....... $48.00
THIS
ITEM IS UNAVAILABLE AT THIS TIME, PLEASE DO NOT ORDER !
Resin
model includes: Correct AWB Body, Hood, Grill, Chassis with Interior Floor, Firewall, Door Panels,
Dash, Front Frame Clip, Taillights & Rear Bumper.
Recommended donor parts:
#SC-103 Drag Racing Driver Figure
#SC-89 Chrysler 8-3/4 Rear End
#SC-55 Front Leaf Spring Assortment Pack
#SC-82 A-100 Lightweight Super Stock Seats
#SC-71 15" Pie Crust Slicks
#SC-39 American 5 Spoke Front Mag Wheels
#SC-87 Inner Rims (deep dish)
#SC-75 Goodyear Blue Streak Skinny Front Tires
#SC-40 American Racing 15" Rear Mag Wheels
#SC-5 Hemi Hilborn Intake Manifold
#SC-24 15" Injector Stacks
#SC-7 AFX Parts Pack
#SC-56 Parchute Assortment Pack
*Front
suspension... use a dropped axle from a Revell '51 Ford Angelia, '51 Henry
J, '29 Ford or Custom pick up, kit.
*Rear suspension.....use a amt/ertl '71 duster
*Real
car was painted metallic burgundy, close color match is PACTRA RC67 met. burgundy
"SCALE MODELING BY CHRIS" has the RAMBUNCTIOUS decals for this kit.
Doug Schultz built this from a resin model.
Scott Kapellusch built this from a resin model.
Rick Shepard built this from a resin model.
THIS ITEM IS UNAVAILABLE AT THIS TIME, PLEASE DO NOT ORDER !
Resin
model includes: Correct AWB '65
Dart Body (with a '66 Dart Front clip), Chassis / Interior Tub (with fire wall,
Floor & door panels), Dash & Cowl (with scoop), Square
tube frame extension (with motor & fuel tank mounts), Front leaf springs,
Grill, Front & Rear Bumpers.
Recommended donor parts:
#SC-103 Drag Racing Driver Figure
#SC-89 Chrysler 8-3/4 Rear End
#SC-82 A-100 Lightweight Super Stock Seats
#SC-57 S/S Cragar Rear Mag Wheels
#SC-87 Inner Rims (deep dish)
#SC-72 AFX - Super Stock Skinny Front Tires
#SC-34 S/S Cragar (zero offset) Front Mag Wheels
#SC-5 Hemi Hilborn Intake Manifold
#SC-24 15" Injector Stacks
#SC-7 AFX Parts Pack
#SC-56 Parchute Assortment Pack
*Recommended
Donor Parts: For rear suspension use- amt. '71 Plymouth Duster 340.
For Slicks use- 9" slicks found in older AMT. kits.
*Paint: Real
car was painted Metallic lavender !
Close paint match is: mix 1 full
bottle of Colors by BOYD # 52704 GRAPE PEARL - with 3/4 of a bottle of
Testors SILVER.
*Use 3/32" Plastic tube for front tube axle.
*See "MODEL NEWS" page for instructions on how to make a front tube straight axle.
Click on photo for new Flip Front-End Instructions.
Charlie Allen's PURPLE TERROR decals.
Steve Tribbey built this from a resin model.
Doug Schultz built this from a resin model.
Scott Kapellusch built this from a resin model.
The
only '66 Dodge Dart in model history !
Never
before seen in 1/25 scale, until now.
*This
can also be built as a factory style '66 Dodge Dart Promo Model *
#SC-9
........ $48.00
THIS
ITEM IS UNAVAILABLE AT THIS TIME, PLEASE DO NOT ORDER !
Decals
for stock Dart & G/T style emblems,scripts & moldings are available
through Keith Marks.
Click on decal for link
Decal includes: 170 - 270 & G/T style markings
Original vintage color's for all makes and models..... Comes in bottles and spray cans.
Lars-Olof Gustavsson built this from a resin model.
Scott Kapellusch built this from a resin model.
Chuck
Boerner is selling new decals for the cars on the bottom row, you can contact
him at: stang1forever@yahoo.com
Or search eBay name..... cboerne
THIS ITEM IS CURRENTY UNAVAILABLE, PLEASE DO NOT ORDER AT THIS TIME !
Use
any Polar Lights Charger or Barracuda Funny Car for donor..... Chassis, Motor & Interior parts.
Check out our "PARTS PAGE" for any Tires, Slicks, Mag Wheels, Rear End, Driver Figure or other parts you may need.
Has
the KING FISH CUDA & AVENGER CUDA Decals for this body
Nostalgia (60's & 70's) Funny Car Grill & Headlight Sheet
DON SCHUMACHER ( INDY WINNER ) '70 CUDA decal
DON SCHMACHER '72 CUDA decal
BIG JOHN decal
DAM YANKEE decal (out of production)
DUNN & REATH decal
CANDIES & HUGHES decal
ROLLIN' STONED decal
STARDUST decal
KEYSTONE KUDA decal
All rights reserved. Do not copy any Speed City Resin bodies or parts without permission and consent.